ALTER RESOURCE QUEUE
Changes the limits of a resource queue.
Synopsis
ALTER RESOURCE QUEUE <name> WITH ( <queue_attribute>=<value> [, ... ] )
where queue_attribute is:
ACTIVE_STATEMENTS=<integer>
MEMORY_LIMIT='<memory_units>'
MAX_COST=<float>
COST_OVERCOMMIT={TRUE|FALSE}
MIN_COST=<float>
PRIORITY={MIN|LOW|MEDIUM|HIGH|MAX}
ALTER RESOURCE QUEUE <name> WITHOUT ( <queue_attribute> [, ... ] )
where queue_attribute is:
ACTIVE_STATEMENTS
MEMORY_LIMIT
MAX_COST
COST_OVERCOMMIT
MIN_COST
Note A resource queue must have either an
ACTIVE_STATEMENTSor aMAX_COSTvalue. Do not remove both thesequeue_attributesfrom a resource queue.
Description
ALTER RESOURCE QUEUE changes the limits of a resource queue. Only a superuser can alter a resource queue. A resource queue must have either an ACTIVE_STATEMENTS or a MAX_COST value (or it can have both). You can also set or reset priority for a resource queue to control the relative share of available CPU resources used by queries associated with the queue, or memory limit of a resource queue to control the amount of memory that all queries submitted through the queue can consume on a segment host.
ALTER RESOURCE QUEUE WITHOUT removes the specified limits on a resource that were previously set. A resource queue must have either an ACTIVE_STATEMENTS or a MAX_COST value. Do not remove both these queue_attributes from a resource queue.
Parameters
name
The name of the resource queue whose limits are to be altered.
ACTIVE_STATEMENTS integer
The number of active statements submitted from users in this resource queue allowed on the system at any one time. The value for ACTIVE_STATEMENTS should be an integer greater than 0. To reset ACTIVE_STATEMENTS to have no limit, enter a value of -1.
MEMORY_LIMIT 'memory_units'
Sets the total memory quota for all statements submitted from users in this resource queue. Memory units can be specified in kB, MB or GB. The minimum memory quota for a resource queue is 10MB. There is no maximum; however the upper boundary at query execution time is limited by the physical memory of a segment host. The default value is no limit (-1).
MAX_COST float
The total query optimizer cost of statements submitted from users in this resource queue allowed on the system at any one time. The value for MAX_COST is specified as a floating point number (for example 100.0) or can also be specified as an exponent (for example 1e+2). To reset MAX_COST to have no limit, enter a value of -1.0.
COST_OVERCOMMIT boolean
If a resource queue is limited based on query cost, then the administrator can allow cost overcommit (COST_OVERCOMMIT=TRUE, the default). This means that a query that exceeds the allowed cost threshold will be allowed to run but only when the system is idle. If COST_OVERCOMMIT=FALSE is specified, queries that exceed the cost limit will always be rejected and never allowed to run.
MIN_COST float
Queries with a cost under this limit will not be queued and run immediately. Cost is measured in units of disk page fetches; 1.0 equals one sequential disk page read. The value for MIN_COST is specified as a floating point number (for example 100.0) or can also be specified as an exponent (for example 1e+2). To reset MIN_COST to have no limit, enter a value of -1.0.
PRIORITY={MIN|LOW|MEDIUM|HIGH|MAX}
Sets the priority of queries associated with a resource queue. Queries or statements in queues with higher priority levels will receive a larger share of available CPU resources in case of contention. Queries in low-priority queues may be delayed while higher priority queries are run.
Notes
GPORCA and the Postgres planner utilize different query costing models and may compute different costs for the same query. The Cloudberry Database resource queue resource management scheme neither differentiates nor aligns costs between GPORCA and the Postgres Planner; it uses the literal cost value returned from the optimizer to throttle queries.
When resource queue-based resource management is active, use the MEMORY_LIMIT and ACTIVE_STATEMENTS limits for resource queues rather than configuring cost-based limits. Even when using GPORCA, Cloudberry Database may fall back to using the Postgres Planner for certain queries, so using cost-based limits can lead to unexpected results.
Examples
Change the active query limit for a resource queue:
ALTER RESOURCE QUEUE myqueue WITH (ACTIVE_STATEMENTS=20);
Change the memory limit for a resource queue:
ALTER RESOURCE QUEUE myqueue WITH (MEMORY_LIMIT='2GB');
Reset the maximum and minimum query cost limit for a resource queue to no limit:
ALTER RESOURCE QUEUE myqueue WITH (MAX_COST=-1.0,
MIN_COST= -1.0);
Reset the query cost limit for a resource queue to 310 (or 30000000000.0) and do not allow overcommit:
ALTER RESOURCE QUEUE myqueue WITH (MAX_COST=3e+10,
COST_OVERCOMMIT=FALSE);
Reset the priority of queries associated with a resource queue to the minimum level:
ALTER RESOURCE QUEUE myqueue WITH (PRIORITY=MIN);
Remove the MAX_COST and MEMORY_LIMIT limits from a resource queue:
ALTER RESOURCE QUEUE myqueue WITHOUT (MAX_COST, MEMORY_LIMIT);
Compatibility
The ALTER RESOURCE QUEUE statement is a Cloudberry Database extension. This command does not exist in standard PostgreSQL.
See also
CREATE RESOURCE QUEUE, DROP RESOURCE QUEUE, CREATE ROLE, ALTER ROLE
